Bombardier SMP800-C Toxic Gas Generation – Toxic Gas Sampling and Analytical Procedures SMP 800-C毒性气体的产生－燃烧烟雾毒性气体的取样和分析流程
EN 2824 – EN 2825- EN 2826烟密度和烟气成分分析
EN 2824 Aerospace series – Burning behavior,determination of smoke density and gas components in the smoke of materials under the influence of radiating heat and flames-test equipment,apparatus and media EN 2824 辐射热和火焰影响下材料烟密度和气体成分的测定-试验设备，装置和介质 EN 2825 Determination of smoke density EN 2825 烟雾密度测定 EN 2826 Determination of gas components in the smoke […]
14 CFR 25 Appendix F, Part I纺织品垂直燃烧测试
14 CFR 25, Appendix F, Part I (vertical test) 14 CFR 25, Appendix F, Part I垂直燃烧测试
CAN/ULC-S135 热量释放测试
CAN/ULC-S135 热量释放测试- 标准名称 CAN/ULC-S135：Standard Method of Test for Determination of Degrees of Combustibility of Building Materials Using an Oxygen Consumption Calorimeter (Cone Calorimeter) CAN/ULC-S135：使用氧耗热量计评定建筑材料燃烧分级测试(锥形量热仪法)
EN 50268电缆烟密度测试
EN 50268-2: Common test methods for cables under fire conditions-Measurement of smoke density of cables burning under defined conditions-Part 2: Procedure EN 50268-2: 着火条件下电线电缆的通用测试标准–在规定条件下燃烧的电缆烟密度测试，第二部分：测试程序及要求 （已被EN61034-2标准取代）
IEC 60331-21额定电压不超过0.6/1.0KV的电缆线路完整性
IEC 60331-21: Tests for electric cables under fire conditions-Circuit integrity-Part 21: Procedures and requirements-Cable of rated voltage up to and including 0.6/1.0 KV IEC 60331-21:在火焰条件下电缆或光缆的线路完整性试验第21部分：试验步骤和要求－额定电压0.6/1.0KV及以下电缆（等同性标准GB/T19216.21）
IEC 60331-11火焰温度不低于750度的单独供火
IEC60331-11Tests for electric cables under fire conditions – Circuit integrity – Part11: Apparatus-Fire alone at a flame temperature of at least 750°C IEC 60331-11第11部分:设备-单在至少750的火焰温度下点火
IEC 60331-2电缆维持线路完整性的能力测试
Tests for electric cables under fire conditions – Circuit integrity – Part 2: Test method for fire with shock at a temperature of at least 830 °C for cables of rated voltage up to and including 0,6/1,0 kV and with an overall diameter not exceeding 20 mm IEC 60331-2着火条件下电缆的试验.电路完整性.第2部分:额定电压高达和包括0.6/1.0 KV,外径不超过20 […]
IEC 60331-1电缆线路完整性测试
IEC 60331-1 Tests for electric cables under fire conditions — Circuit integrity — Part 1: Test method for fire with shock at a temperature of at least 830℃ for cables of rated voltage up to and including 0,6/1,0 kV and with an overall diameter not exceeding 20mm. IEC 60331-1在火焰条件下电缆的线路完整性试验–第1部分：额定电压0.6/1.0kV及以下、总直径大于20mm电缆在温度不低于830℃冲击火焰下的试验方法
EN 60332-3-23线缆成束燃烧测试B类
EN 60332-3-23:2009 Tests on electric and optical fibre cables under fire conditions Part 3-23: Test for vertical flame spread of vertically-mounted bunched wires or cables – Category B EN 60332-3-23:2009测试导电纤维的火灾情况下电缆第3-23部分和光：垂直安装的成束电线或电缆–B类垂直火焰蔓延试验